关于找未连丝的座标，请问各位怎么找呀，在线等

dolly507

(00:00:01) Starting new drawing...
\i (00:00:01) trapsize 1029
\i (00:00:01) trapsize 1029
\i (00:00:02) open
\i (00:00:04) fillin "X300-DDR2-0909-A.brd"
\t (00:00:04) Opening existing drawing...
\i (00:00:04) trapsize 6
\i (00:00:08) reports
\i (00:00:10) setwindow form.rpt
\i (00:00:10) FORM rpt rpt Unconnected Pins
\i (00:00:11) FORM rpt execute  
\t (00:00:11) Starting Generating report, please wait......
\e (00:00:11) report had errors -  use Viewlog to review the log file.
\e (00:00:11) A problem occurred - please check the logfile (using Viewlog).
\i (00:00:12) fillin confirm

欧阳小雪梦

不明白你的意思[em06]

dolly507

怎么没人回答呀

dolly507

我用tools/reports\unconnected pins检查到未连接的线有上面说的，我怎么准确的把那些未连接的找出来或

markwang

在reports中有坐标的呀，你可以按照坐标找到net,没有连接就是net的两端。你也可以把鼠线全打开，关闭所有的层，你可以开到没有连接的鼠线

dolly507

我现在的问题是不知道怎么准确的找到那个坐标

mandylee

你把allegro關掉後再進去run一次試試看

欧阳小雪梦

12V From: CE2.1 (2008.2 1241.5) T R33.2 (537.0 1617.5) From: CE2.1 (2008.2 1241.5) T J2.13 (1575.0 -135.0) From: F1.1 (2248.2 1075.5) T C8.1 (2588.0 1483.5) From: F1.1 (2248.2 1075.5) T CE2.1 (2008.2 1241.5) 3V3 From: R34.2 (2345.0 1617.5) T R4.2 (2797.0 1617.5) From: R27.2 (424.0 1617.5) T R34.2 (2345.0 1617.5) From: R27.2 (424.0 1617.5) T C3.1 (144.5 1681.5) From: U1.8 (756.0 600.0) T R27.2 (424.0 1617.5) From: U2.6 (1251.6 -815.4) T U1.8 (756.0 600.0) From: U2.26 (1448.4 -815.2) T U2.6 (1251.6 -815.4) From: U2.26 (1448.4 -815.2) T U2.23 (1448.4 -874.2) From: J2.1 (2175.0 -135.0) T U2.26 (1448.4 -815.2) 应该是上面这样的啊？

欧阳小雪梦

你是不是report错了啊[em07]

dolly507

我用tools/reports\unconnected pins检查到未连接的线有上面说的：

出现下面的错误呀

\t (00:00:01) allegro 15.1 p002 (v15-1-31A) i86 \t (00:00:01)

\t (00:00:01) Starting new drawing... \i (00:00:01) trapsize 1029 \i (00:00:01) trapsize 1029 \i (00:00:03) open \i (00:00:06) fillin "X300-DDR2-0909-amy.brd" \t (00:00:06) Opening existing drawing... \t (00:00:07) Grids are drawn 16.00, 16.00 apart for enhanced viewability. \i (00:00:07) trapsize 593 \i (00:00:09) reports \i (00:00:12) setwindow form.rpt \i (00:00:12) FORM rpt rpt Unconnected Pins \i (00:00:13) FORM rpt execute \t (00:00:13) Starting Generating report, please wait...... \e (00:00:13) report had errors - use Viewlog to review the log file. \e (00:00:13) A problem occurred - please check the logfile (using Viewlog). \i (00:00:15) fillin confirm \i (00:00:16) FORM rpt cancel

怎么看这个是什么错误　呀